Table of Contents


Pfahl Fault System (PFFS)

Structure ID: PFHQ / PFH
Fault Section IDs: PFHQ_01 – PFHQ_22 / PFH_01 – PFH_04
Related terms: Pfahl, bavorský křemenný val (in Czech); Pfahl-Störungssystem (De); Bavarian Pfahl shear zone (En)

Editor: Ivan Prachař
Last update: 6. 12. 2022

new tab with life map




← click the image to open new tab with interactive map

General description

The Pfahl is NW-SE striking, steep to NE dipping fault system which runs from Schwarzenfeld in Oberpfälz Forest, through the Bavarian Forest (D), along the border with the Czech Republic, to Klafferstraß (D) on the German-Austrian border and then runs via Ulrichsberg, through the Mühl river valley to Haslach an der Mühl and further to Untergeng in the Große Rodl valley, where it is cut off from the Rodl fault system (see also http://resource.geolba.ac.at/ structure/147). The German word ‘‘Pfahl’’ makes reference to the quartz lode running through the Bavarian Forest in the length of 150 km (see all Fsections PFHQ).

This fault system is evident in the Moldanubian complex (see Fig. 1), mainly due to the distinctive quartz lode, along which there are a number of smaller granitoid massifs of the Weinsberg and Eisgarn type.

new tab with life map

Fig. 1: Sketch of the Pfahl fault system (PFHQ – quartz vein and PFH section) depicted on the raster geological map of Bavaria (1: 500 000) and Upper Austria (1: 200 000).

It is assumed that the fault zone continues to the Franconian Jura in the form of direction-related faults (see Geological map of Bavaria 1 : 500 000). E.g. as parallel Amberg-Sulzbach fault (NW-SE) or Freihunger fault (see REYNHOLD, 2005). A fault that is parallel to Pfahl limits the half-graben “Bodenwöhrer Senke” between Pösing and Schwarzenfeld, where Permo-carboniferous and Upper Cretaceous sediments are deposited (see upper left corner of Fig. 1).


Fault structure and dip

In the Bavarian Forest, the fault acts as a Pfahl quartz lode 150 km long. Over long distances, this quartz wall rises up to approximately 30 meters above the surroundings thanks to weathering resistance (see Fig. 2). The lode width is around 120 m. Dip of the lode is steep to the NE.

new tab with life map

Fig. 2: The „Große Pfahl“ near Viechtach (D). Photo Bavarian Forest Nature Park. (https://www.arberland-bayerischer-wald.de/pfahl-významný-přírodní-památník/150/5631/21516).

The vein consists of 95-98% quartz (see MESCHEDE, 2015). The formation of a vein is explained as a long-lasting hydrothermal process where cyclic dissolution, precipitation and fragmentation of quartz occurred on large scale (see YILMAZ ET AL., 2014).

The mylonites are also present in the Pfahl Zone. They are strongly overprinted by subsequent brittle deformation. As one of the major dextral shear zones the foliation dips steeply to the NE with a sub-horizontal stretching lineation. On a macroscopic and a microscopic scale, the mylonites are developed as highly deformed rocks comprising a fine-grained matrix flowing around large feldspar clasts. Quartz most commonly occurs as recrystallized grains forming bands (see BRANDMAYR ET AL., 1997).


Cross structures and Segmentation

More significant segmentation of the Pfahl can be observed near Haslach an der Mühl, where a distinct quartz vein is terminated. Here it is also possible to observe topo-lineaments of the NNE-SSW direction, which follow the faults of the Lhenice shear zone in the north. The course of the Pfahl fault system also turns gradually from NW-SE to NNW-SSE. Between Haslach and crossing with the Rodl fault, the Pfahl fault system is not accompanied by a quartz lode (see Raster geological map of Upper Austria 1 : 200 000).


Scarp morphology

The morphological manifestation of the Pfahl fault zone between Schwarzenfeld and Haslach an der Mühl is highlighted by a quartz wall rising up to 30 m (see Fig. 2).


Seismicity

To be revisited after completion of earthquake catalogue. FIXME


Pre-Miocene evolution

The beginning of Pfahl shear zone formation is dated to the Early Paleozoic in connection with the formation of the Moldanubian nappes as a result of large-scale northeastward directed transpression of an Early Paleozoic terrane. After this main tectonic event, shear activity initiated on the dextral shear zone set of the Pfahl and Danube Shear Zones and in the sinistral Rodl / Karlstift / Vitis Shear Zones (see BRANDMAYR ET AL., 1997), as shown in Fig. 3.

new tab with life map

Fig. 2: Initial shear zone activity in the Danube (DF), Pfahl (PF), Rodl (RF), Karlstift (KSF) and Vitis (VF) Shear Zones. Arrows indicate major compression directions. Adopted from BRANDMAYR ET AL. (1997).

However, the main ductile deformation phase is dated to the Late Variscian, showing mainly dextral direction of movement (see http://resource.geolba.ac.at/structure/147). This corresponds to the age of syn-kinematic mylonites (so-called palites - feldspar-phyric massive rock) and other dykes, which was determined by SIEBEL ET AL. (2005) at 332.7-334.5 Ma (Lower Carboniferous). The authors further state that the shear zone controlled the siting of these intrusions and that the shear zone was active when the magmas intruded. Dating also showed a long-lasting cooling history after mylonitization.


Fault activity in late Cenozoic

Tertiary

It is considered that during Miocene a brittle reactivation with the same kinematics went on. (see BRANDMAYR ET AL., 1997; BÜTTNER, 2007). Post Miocene activity of the Pfahl fault zone has not been proven, yet.

Quaternary

There is no evidence that this fault system was active in the Quaternary.


(See layer Local evidence on a map. The sites are listed in south-to-north order.)

They are not yet processed.m(

Main data sources for fault map

See text above.


Other notes


References